THIS TOOL CAN BE USED FOR REMOVAL, INSTALLATION, AND ADJUSTMENT OF ANY SIGHT, FRONT AND REAR, ON ALL GLOCK MODELS.

REAR SIGHT INSTRUCTIONS

1. UNLOAD AND CHECK THE GUN, MAKE SURE THAT THE GUN IS UNLOADED.
2. Disassemble the slide or lock the slide to the rear.
3. Make sure the two lower screws are flush with, and that the swivel head screws are against the inside walls of the tool as shown in picture 1 (Starting Position).
4. Insert the slide in the lower opening of the sight tool with the front sight tool facing you.  The rear end of the slide should be flushed with the back of the sight tool as shown in picture 2.
5. Turn the lower screws with the Allen Wrench to lock the slide in place.
6. Slight Removal, Installation, Adjusting:

    a)    Removal: The tool should be facing you with the front sight tool away from you.  Turn the left 'T' handle until the swivel head is against the sight.  Continue to turn the handle until the rear sight is at the end of the groove then manually remove as shown in picture 3.  Then return the tool to the Starting Position.
    b)    Installation:  Place the sight manually inside dovetail from the right.  Turn the right 'T' handle until it is against the sight as shown in picture 4.  Continue to turn the handle until the desired location is reached.  Then return the tool to the Starting Postion.
    c)    Adjusting:  Turn either the left or right 'T' handle until desired location is reached.  Then return the tool to the Starting Position.

FRONT SIGHT INSTRUCTIONS

1. UNLOAD AND CHECK THE GUN, MAKE SURE THAT THE GUN IS UNLOADED.
2. Disassemble the slide.
3. Take off the fixed front sight with a pair of pliers. The sight will just pop out.
4. Put the front sight in place (be sure that the sight is facing up and to the rear).
5 Put the base of the sight screw on the front sight tool and apply some red Loctite.
6. Install the sight crew into the front sight from the underside of the slide as shown in picture 5.
7. Align the front sight with a pair of pliers.

Stock No.	Description	Retail Price	Your Price
GMST	Sight Tool for removal, installation, and adjustment of front and rear sights.	$120.00	$87.00
GMSTADJ	Sight Tool for removal, installation, and adjustment of front and rear sights with Glock adjustable sights.	$145.00	$107.00
GMSTMEP01	Sight Tool for removal, installation, and adjustment of front and rear sights with 6.5mm Meprolight night sights	$195.00	$145.00
GMSTMEP04	Sight Tool for removal, installation, and adjustment of front and rear sights with 6.9mm Meprolight night sights	$195.00	$145.00
GMSTMEPADJ	Sight Tool for removal, installation, and adjustment of front and rear sights with Meprolight adjustable sights.	$225.00	$180.00
GMSTTRIJ01	Sight Tool for removal, installation, and adjustment of front and rear sights with 6.5mm Trijicon night sights	$210.00	$168.00
GMSTTRIJ04	Sight Tool for removal, installation, and adjustment of front and rear sights with 6.9mm Trijicon night sights	$210.00	$168.00

Complete Stock Competition Trigger Package - 3.5# Trigger pull
Glockmeister has put together a package that will allow the Glock enthusiast to add performance to his/her gun with a minimum of effort. With the kit, the shooter will be able to switch between their competition trigger set-up and their stock set-up with the removal of a couple of pins. The kit includes the stock competition trigger kit mounted in a new trigger mechanism housing (for the specific caliber) with a hand selected trigger with trigger bar assembly - completing the drop-in package. This is a complete package, so there is no juggling of small parts necessary. A major benefit to this package is the fact that you retain the carry parts for replacement if you sell the gun or periodically use the gun for carry. Additionally, the gun does not have to go out to an Armorer for an extended period of time for modification. The unit is tested for perfection - it is one of our finest pieces of work. Add $10.00 for an adjustable trigger stop (the adjustable trigger stop removes the bounce at the end of the trigger pull). This is a competition/sport shooting package, it is not intended for duty or carry purposes.

Stock Competition 3.5 Pound Connector
This is a Stock 3.5 pound connector . The connector will help reduce the stock 5.5 pound trigger pull to 3.5 to 4 pounds. This is a competition/sport shooting part, it is not intended for duty or carry purposes.

Modified Carry Trigger Kit
This is a Factory Stock 3.5 pound connector packaged with a Factory Stock NY trigger spring. This package is put together for those that wish to replicate a revolver pull for the first shot.close to a revolver pull that you can get - this gives the shooter a fairly steady stiff pull from start to finish.

Glockmeister Competition Trigger Kit
This is a Factory Stock 3.5 pound connector packaged with a Glockmeister competition trigger spring. Not intended for duty or carry purposes.

Competition Trigger W/Trigger Bar Assembly
Glockmeister offers this hand selected factory part that will allow the Glock enthusiast to add performance to his/her gun with a Competition Trigger Stop. This is a competition assembly, it is not intended for duty or carry use.
 
 

Stock No.	Description	Retail Price	Your Price
G721	3.5 Pound Trigger - Stock Glock 3.5 Pound Connector - For ALL Glock Models	N/A	$25.00
GMTSK1	Glockmeister competition trigger spring For all models	$3.00	$2.50
GM721CCW	3.5 Pound Trigger - Modified Glock Carry Package - Stock 3.5 Pound Connector - and a NY Trigger Spring - For ALL Glock Models	N/A	$27.00
GM721COMP	3.5 Pound Trigger - Stock Glock Comp Package - Stock 3.5 Pound Connector and a Competition Trigger Spring - Gives a Light Take-Up - Looks Like a Stock Trigger Spring - For ALL Glock Models	N/A	$27.00
GMUCSTP17	Complete Stock Competition Trigger Package - Models G17,17L,34, (add $10.00 for an adjustable trigger stop)	$87.00	$62.00
GMUCSTP19	Complete Stock Competition Trigger Package - Models G19,26, (add $10.00 for an adjustable trigger stop)	$87.00	$62.00
GMUCSTP21	Complete Stock Competition Trigger Package - Models G20, 21 (add $10.00 for an adjustable trigger stop)	$87.00	$62.00
GMUCSTP22	Complete Stock Competition Trigger Package - Models G22, 24,31,35 (add $10.00 for an adjustable trigger stop)	$87.00	$62.00
GMUCSTP23	Complete Stock Competition Trigger Package - Models G23, 27,32,33 (add $10.00 for an adjustable trigger stop)	$87.00	$62.00
GMUCSTP30	Complete Stock Competition Trigger Package - Models G29, 30 (add $10.00 for an adjustable trigger stop)	$87.00	$62.00
GM357	Glockmeister Drop-in Trigger W/Trigger Bar with trigger stop. Glock Models 17,17L,22,24,31. The adjustable trigger stop removes the bounce at the end of the trigger pull. Intended for competition use only.	N/A	$40.00
GM2303	Glockmeister Drop-in Trigger W/Trigger Bar with trigger stop. Glock Models 19,23,25,26,27,28,32,33. The adjustable trigger stop removes the bounce at the end of the trigger pull. Intended for competition use only.	N/A	$40.00
GM4417	Glockmeister Drop-in Trigger W/Trigger Bar with trigger stop. Glock Models 20,21. The adjustable trigger stop removes the bounce at the end of the trigger pull. Intended for competition use only.	N/A	$40.00
GM1194	Glockmeister Drop-in Trigger W/Trigger Bar with trigger stop. Glock Models 29,30. The adjustable trigger stop removes the bounce at the end of the trigger pull. Intended for competition use only.	N/A	$40.00

GLOCKMEISTER COMPETITION OPTICS MOUNT FOR FINGERGRIP/RAIL MODELS
WE HAVE A NEW OPTIC MOUNT THAT ALSO FITS ON YOUR G20 AND 21. - BRAND NEW

GLOCKMEISTER CUSTOM COMPETITION OPTICS MOUNT FOR FINGERGRIP/RAIL MODELS 17,18,19,20, 21, 22,23,24,25,31,32,34,35  - NEW!!!
The Glockmeister CUSTOM Competition Optics Mount is precision CNC machined aircraft Aluminum engineered to be the lightest (58.5 grams), most corrosion resistant and strongest mount on the market. It is designed to allow the gun to be field stripped without removing the mount, it is designed to be unobtrusive to left and right hand shooters, it does not affect ejection and allows the shooter to use the standard sights without removing the mount. The mount is anodized to Mil-A-8625 specifications, it is constructed using stainless steel thread inserts for extra strength and uses a custom made trigger pin constructed of 416 stainless steel that is hardened to 42 Rc.
 
 

The mount is designed around the C-More Slide Ride Optical Sight. We tested all of the other major optics that could be mounted on a Glock and found that the C-More performed at the top under the toughest shooting conditions. The C-More lead the rest in weight to size ratio, intensity of dot, field of view, reliablity and durability. We have added the new weaver base to the mount, so shooters can use their existing weaver base optics such as Tasco and Aimpoint.

Please note that this mount is designed for the above mentioned finger grip/rail models. The mount comes in Black, Red and Blue and Silver.

Stock No.	Description	Your Price
GMOPTIC940	Glockmeister Optics Mount - Black  SPECIAL PRICE REDUCED FROM $100!!	$75.00
GMOPTIC940WB	Glockmeister Optics Mount - Black - With Weaver Base SPECIAL PRICE REDUCED FROM $!25!!	$100.00
WBASE	Weaver Base for Glockmeister Mount SPECIAL PRICE REDUCED FROM $30!!	$25.00
CMORE	C-More Slide Ride Optical Sight (for use with the Glockmeister Optics mount - combination pictured above).	$230.00 (sight only)
GMOPTIC940CMORE	Glockmeister Optics Mount with C-More SPECIAL PRICE REDUCED FROM $330!!	$300.00

Glockmeister has taken some time to develop a magwell that is just the right size and accepts all of the magazine extensions on the market. Other magwells on the market are too small, too big or they only accept certain mag extensions. We took the input from our shooters and our customers and designed a magwell that fits most shooters' needs. It is made from aircraft grade aluminum and measures .60 inches in height. The magwell is anodized black, red or blue and there are two different sizes for the 9/40. (one for the finger groove and one for the non-finger groove receivers). Colors are Black and Brass. Magwell for 10/45 only in black and fits both Finger groove and Non-Finger groove.
 

Factory Glock Extended Slide Stop Lever
A little longer than standard unit (see photos above) for better leverage. The factory Glock extended slide stop lever has a built-up portion that allows the shooter to get a better grip when releasing at increased speeds. Specifically designed for the shooter that engages the longer slide releases unintentionally. This slide stop lever is designed for a quicker, smoother, and easier release action. There is no need to change hand, eye or head position - due to the feel of the lever. The Glock Extended Slide Stop Lever also reduces recovery time for both strong and weak hands.
 
 

Glockmeister Extended Mag Catch
We perfected the ultimate drop-in extended mag catch. This extended mag catch is a drop-in unit that utilizes durable anodized aircraft aluminum in conjunction with a modified stock mag catch for trouble-free operation. You don't have to worry about metal coming in contact with your expensive mags, this is made from a stock mag catch - plastic to plastic contact is maintained. You can engage the snag free Extended Mag Catch without breaking your grip (turning the gun) - it is one of our finest accessories to date. At the above right the extended mag catch is displayed assembled and in its two major parts. On the left it is installed in the G20. Note that the Extended Mag Catch does not interfere with the holster in our ATA line - it should not interfere with most holsters.